Trust Wallet USDT TRC-20 Fee: How to Send Without Burning TRX

When you send USDT TRC-20 from Trust Wallet, the wallet shows a network fee in TRX. That fee pays for TRON network resources: if your address has no energy, the network burns TRX instead. If you get energy on your address first, the transfer goes through without burning TRX. Below are the steps, the savings math and the mistakes that cause TRX to be burned anyway.

Why Trust Wallet charges TRX for a USDT transfer

USDT on TRON is a TRC-20 smart contract, and the network uses energy for every transfer. The wallet signs and sends the transaction from your address, and the address itself pays for it: with energy if it has some, or with burned TRX. As of Oct 5, 2026, the burn price is 100 SUN per unit of energy.

That gives two typical amounts:

Where you send	Energy needed	Burned without energy
To an address that already holds USDT	about 65,000	6.5 TRX
To an address with no USDT yet	about 131,000	13.1 TRX

Energy on your address works with any wallet you send from. It is a resource of the address on the network, not a Trust Wallet setting, so there is nothing to turn on in the app.

What you need

• Trust Wallet with USDT on TRON (TRC-20) in your balance.
• The TRON address of that wallet. It starts with the letter T.
• To know whether the recipient’s address holds USDT: that decides how much energy you need.
• A little TRX in the wallet. A transfer also uses bandwidth, and if the free daily allowance runs out, the network charges a small amount of TRX for it.

Step-by-step guide

1. Copy your TRON address in Trust Wallet

In Trust Wallet, open USDT on the TRON network specifically. Your wallet may hold USDT on several networks, and each one has its own network label. Go to the receive screen and copy the address under the QR code. A TRON address starts with T and is 34 characters long.

If you have several wallets in Trust Wallet, make sure you copy the address of the one you will send from. Energy on a different address will not pay for this transfer.

2. Work out how much energy you need

Look up the recipient’s address in the TronScan block explorer. If USDT is already among the tokens on that address, about 65,000 energy is enough. If there is no USDT there, plan for about 131,000. For several transfers, add the amounts up.

3. Rent energy to your address

In the UsdtPull app, enter the address you copied, the amount of energy and the rental period. The service only needs the address: it does not need your Trust Wallet recovery phrase or keys, and you should never share them with anyone. Placing an order step by step is covered in the guide on how to buy energy.

4. Check that the energy has arrived

Open your address in TronScan. The address page shows the available energy, and the delegation appears in the transaction list. Send USDT only after that: if you send earlier, the network will burn TRX first.

5. Send USDT from Trust Wallet

Go back to Trust Wallet, open USDT on TRON and send the transfer as usual: paste the recipient’s address, enter the amount, check the details and confirm. Do it within the rental period.

The wallet may still show an estimated network fee in TRX. The network does the final math: it uses the energy on your address first and burns TRX only for any shortfall.

6. Check the result in TronScan

Open the transaction in the block explorer. Its page shows how much energy was used and whether any TRX was burned. If there was enough energy, no TRX was burned for energy.

How much you save

As an example, take a rental rate of 32 SUN per unit of energy for 1 hour. The exact price is shown in the app before you pay.

Transfer	TRX burn	Energy rental (example)	Difference
Standard, 65,000 energy	6.5 TRX	2.08 TRX	4.42 TRX
To a new address, 131,000 energy	13.1 TRX	4.19 TRX	8.91 TRX

If you send several transfers a week from Trust Wallet, the difference adds up quickly. Current reference prices are on the energy pricing page.

If you send often

Energy use does not depend on the amount: sending 10 USDT and 10,000 USDT uses the same energy. So count transfers, not amounts.

• Several transfers at once: add up the energy for each one, 65,000 for a standard transfer and 131,000 for a transfer to a new address, and pick a rental period that leaves time for all of them.
• Transfers every day: it is easier to plan one rental for the whole day’s volume than to order energy before every transfer.
• A steady flow of payouts from one address: this is what always-on energy (energy kept on your address) is for. It is topped up automatically after each transaction.

Common mistakes

• USDT on the wrong network. TRON energy pays only for transfers on TRON. If you picked USDT on another network, the fee follows that network’s rules.
• Energy went to a different address. Compare the first and last characters of the address in your order and in Trust Wallet.
• 65,000 energy, but the recipient is new. The transfer needs about 131,000 energy, and the network covers the shortfall by burning TRX. If there is not enough TRX for that, the transfer fails with an OUT OF ENERGY error.
• The rental period ended. After the period, the energy returns, and the transfer is paid by burning TRX again.
• Energy ordered for one transfer, but two were sent. The first transfer uses the energy, and the second one burns TRX.
• The transfer was sent before the energy arrived. The network pays for it by burning TRX, and the energy stays on your address until the period ends.

Is it safe

Energy rental does not need access to Trust Wallet. The service sends energy to your address, and you still sign every transfer yourself in your own wallet. The energy delegation is visible in the block explorer, and when the period ends, the energy returns on its own, with nothing for you to do.

If anyone asks for your recovery phrase or private key “to connect energy”, it is a scam. Renting energy only needs your address. More answers about how energy works are in the FAQ.